Catalogue
English

7FX25 - Flat trusses 25 cm

 

7FX25 - Flat trusses 25 cm Linear trussDimensions of the aluminium casting plate
View all
7FX M10 - Connection kit with bolts No. 2 bolts + No. 2 nuts M10 7FX FC - Fast connection kit 2 No. 2 x 7KSG - Spigot + No. 4 x 7KSP - Conic dowel pin + No. 4 x 7KCP - Split pin
7FX25 K 2 - Dado 4 ways-2 nodes7FX25 K 4 - Dado 6 ways-4 nodes To compose corners and intersections without using fixed corners.Every Dado 7FX25 K 2 / K 4 requires a connection kit 7QX K FC for each connection between Dado and truss.7FX K FC - Connection kit for Dado 4 ways-2 nodes No. 2 x 7KSM - ½ spigot + screw 10x25No. 2 x 7KSP - Conic dowel pinNo. 2 x 7KCP - Split pinNo. 2 bolts7TZ30 K 01 - Assembly template For Dado connection kit
Floor plate
Clamp modules 1 - short2 - long
2 ways horizontal corners 1 - 60°2 - 90°3 - 120°4 - 135°
2 ways vertical corners 1 - 60°2 - 90°3 - 120°4 - 135°
3 ways horizontal corners 1 - 90° horizontal right2 - 90° horizontal left3 ways vertical corners 3 - 90° vertical right4 - 90° vertical left
Load table of linear trusses

↓ - Center point load
↓ ↓ - Point load at 1/3
↓ ↓ ↓ - Point load at 1/4
↓ ↓ ↓ ↓ - Point load at 1/5
↓↓↓↓↓↓↓↓↓↓↓↓ - Uniformly distributed load

The load table was prepared in accordance with UNI ENV 1999-1-1 (Eurocode9).
When calculating the allowable loads shown in the table, it is assumed that the trusses are simply supported at the end connection and that static loads will be applied to the node points.
The application of the load shall be on the centre line of the truss.
The values shown in the table are the allowable statics loads that can be applied to the truss.
This is the live load or the payload.
The self weight of the truss was taken into account when calculating the values in the table.
It should be noted that these are idealised loading conditions and that the User shall re-analyze the truss for the loading conditions which prevail for the application being considered.
Cords
aluminium extruded tube Ø 50 x 1,5 mm - EN AW 6005 T6
Diagonals
aluminium extruded tube Ø 14 x 1,5 mm - EN AW 6060 T6
Ends
aluminium casting plate - EN AC 42200 T6

7FX25
Standard lengths of linear trusses
article
length ..... weight
. cm ............ kg
7FX25 T 012
..12,5 ......... 0,8
7FX25 T 025
..25 ............ 1,0
7FX25 T 050
..50 ............ 1,5
7FX25 T 100
100 ............ 2,2
7FX25 T 150
150 ............ 3,0
7FX25 T 200
200 ............ 3,9
7FX25 T 250
250 ............ 4,6
7FX25 T 300
300 ............ 5,4
7FX25 T 350
350 ............ 6,2
7FX25 T 400
400 ............ 7,0